Nota: Ingredientes incluidos en la lista de productos químicos restringidos
EC/CAS
13463-67-7
Nombre del producto químico
Reaction mass of titanium dioxide and silver chloride
Concentración
≥20-≤50
EC/CAS
123-86-4
Nombre del producto químico
acetic acid, butyl ester
Concentración
≥1.0-≤5.0
EC/CAS
21645-51-2
Nombre del producto químico
Aluminium hydroxide
Concentración
≥1.0-≤5.0
EC/CAS
64742-95-6
Nombre del producto químico
Solvent naphtha (petroleum), light arom
Concentración
≤2.0
EC/CAS
91-20-3
Nombre del producto químico
Naphthalene,3
Concentración
<1.0
EC/CAS
108-88-3
Nombre del producto químico
Toluene
Concentración
<1.0
EC/CAS
77-99-6
Nombre del producto químico
1,1,1-trimethylolpropane
Concentración
≤1.0
Información General
Fecha de revisión:
2025-12-03
A. Nombre del producto
POLYCRON SUPER WHITE
1.5 Uso recomendado:
Aplicaciones industriales
1.2.2. Usos desaconsejados
No aplicable
Número de emergencia
1-888-774-2001
IÍconos en FDS
Información de la empresa
Empresa
PPG Industries, Inc
Información GHS
Palabra clave
Peligro
Hazard Codes
Declaraciones de peligro (CLP)
H226, H316, H317, H350, H361
Declaraciones de peligro
Código
Declaraciones
H226
Flammable liquid and vapour
Sección 2
SECCIÓN 2: Identificación de los peligros
Ingrediente (s) con toxicidad aguda desconocida
32% (oral), 32% (dermal), 65.2% (inhalation) This product contains TiO2 which has been classified as a GHS Carcinogen Category 2 based on its IARC 2B classification. For many products, TiO2 is utilized as a raw material in a liquid coating formulation. In this case, the TiO2 particles are bound in a matrix with no meaningful potential for human exposure to unbound particles of TiO2 when the product is applied with a brush or roller. Sanding the coating surface or mist from spray applications may be harmful depending on the duration and level of exposure and require the use of appropriate personal protective equipment and/or engineering controls (see Section 8).
Palabra de advertencia
Warning
Indicaciones de peligro
Flammable liquid and vapor. Harmful if inhaled. May cause drowsiness or dizziness. Suspected of causing cancer.
Prevención
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves, protective clothing and eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use only outdoors or in a well-ventilated area. Avoid breathing vapor.
Respuesta
IF exposed or concerned Get medical advice or attention. IF INHALED Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER or doctor if you feel unwell. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water.
Almacenamiento
Store locked up. Store in a well-ventilated place. Keep container tightly closed.
Eliminación
Dispose of contents and container in accordance with all local, regional, national and international regulations.
Información suplementaria
Sanding and grinding dusts may be harmful if inhaled. Repeated exposure to high vapor concentrations may cause irritation of the respiratory system and permanent brain and nervous system damage. Inhalation of vapor/aerosol concentrations above the recommended exposure limits causes headaches, drowsiness and nausea and may lead to unconsciousness or death. Avoid contact with skin and clothing. Wash thoroughly after handling. Emits toxic fumes when heated.
2.3. Otros riesgos
Prolonged or repeated contact may dry skin and cause irritation.
2.1 Clasificación de la sustancia o de la mezcla
ACUTE TOXICITY (inhalation) - Category 4 CARCINOGENICITY - Category 2 SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Narcotic effects) - Category 3 Percentage of the mixture consisting of ingredient(s) of unknown acute toxicity: 32% (oral), 32% (dermal), 65.2% (inhalation) This product contains TiO2 which has been classified as a GHS Carcinogen Category 2 based on its IARC 2B classification. For many products, TiO2 is utilized as a raw material in a liquid coating formulation. In this case, the TiO2 particles are bound in a matrix with no meaningful potential for human exposure to unbound particles of TiO2 when the product is applied with a brush or roller. Sanding the coating surface or mist from spray applications may be harmful depending on the duration and level of exposure and require the use of appropriate personal protective equipment and/or engineering controls (see Section 8).